!! This website has permanently moved to this new domain: https://www.incefilter.com

Filter Pressure Gauges: Check Accuracy Before Calculating Differential Pressure

Subtracting two pressure readings does not remove the errors in those readings. When a small filter pressure difference is calculated from two much larger line pressures, gauge range and accuracy can materially affect the result. Review the measurement arrangement before using it to accept a filter or set maintenance actions.

This guide helps buyers define instrumentation requirements with an INCEFILTER stainless steel filter housing enquiry. Instrument availability, supply and suitability must be confirmed in the quotation.

Read what the accuracy percentage refers to

Check whether the instrument specification expresses accuracy as a percentage of full scale, span, reading or another stated basis. These descriptions are not interchangeable. WIKA’s pressure-measurement handbook highlights the need to identify the reference value when reporting error.

Also distinguish display resolution from accuracy. A display with more digits does not, on that fact alone, establish a smaller measurement error. Obtain the relevant specification for the instrument and operating conditions.

Work through a simple error-bound example

Suppose, purely for illustration, two gauges each have a 0–10 bar range and a stated error limit of ±1% of full scale under the applicable conditions. Each reading can then have an error of ±0.10 bar. Subtracting the readings gives a conservative worst-case combined error bound of ±0.20 bar, because the errors may act in opposite directions.

If the indicated inlet and outlet pressures are 6.0 and 5.8 bar, the calculated difference is 0.2 bar. That difference is the same size as the illustrative combined error bound. This demonstrates the need to check suitability; it is not a calibration result, a complete uncertainty budget or an INCEFILTER instrument specification.

Do not use this worst-case addition as a substitute for a formal uncertainty analysis where one is required. An instrument specialist should assess the actual error sources and decision margin.

Specify the duty for a differential-pressure instrument

A dedicated differential-pressure instrument can be appropriate when two separate gauges cannot resolve the required difference. WIKA emphasizes that the instrument’s working-pressure capability matters as well as its differential range. A low differential range does not mean the device can withstand only that amount of line pressure—or that any device can tolerate the system pressure.

Requirement What to provide
Measurement range Expected clean and loaded-filter differential pressure.
Line pressure Normal and relevant maximum pressure at the connections.
Process conditions Liquid, temperature, pulsation and relevant transient conditions.
Decision requirement The smallest difference that must be resolved for acceptance or action.
Installation Measurement points, connection details and responsibility for accessories.

Keep installation and calibration records with the readings

Identify the instruments and their verification status. Ensure the readings refer to the intended pressure points, compatible units and references, and comparable operating times. Installation or instrument work must follow the site’s approved isolation procedures.

Use the filter differential-pressure log to preserve the process conditions alongside the measurements. This article addresses instrument selection; the log addresses interpretation of operating trends.

Send INCEFILTER your housing and monitoring requirements with the process duty, proposed pressure points, required measurement capability and quantity. Ask the quotation to identify supplied ports, instruments and accessories separately, with final instrumentation approval assigned to the responsible engineer.

Technical references: WIKA pressure-measurement handbook and WIKA differential-pressure introduction. No WIKA supply or partnership is implied.

TAGs: pleated liquid filter cartridges china 5 micron filter wholesaler how to choose industrial filter bags 0.22 Micron Pleated Filter Cartridges industrial liquid filter bags Polyester Felt Liquid Filter Bag Pleated Filter Cartridge Manufacturer Pleated Filter Cartridge Factory Pleated Liquid Filter Cartridges How to Choose a Reliable Pleated Filter Cartridge Manufacturer Pleated Liquid Filter Cartridges pleated membrane cartridges

Request a Quote

Our experts are here to help. We will respond within 24 hours to your request.

Get in Touch with Us

EMAIL: sales6@incefiltration.com
Mobile/WhatsApp: +86 186 3308 5625
TEL: +86 (311) 8968 1588
TIME: Monday-Friday 8:00am - 5:30pm (CST)

Request a Sample

Need a closer look? Most products have samples available to ensure you are ordering the correct product for your needs. Some restrictions may apply.

Send Us a Message

Tell us what you need, and we'll help you get quotes.

Mobile/WhatsApp: +86 186 3308 5625 Email: sales6@incefiltration.com



    Filtration Engineer
    ● Online
    ×
    WhatsApp