!! This website has permanently moved to this new domain: https://www.incefilter.com

Filter Mesh Open Area: Compare Thread Diameter at the Same Aperture

Two woven meshes with the same aperture can have different open areas. The space occupied by the threads also matters. When reviewing a replacement, request the opening, thread diameter and construction together instead of accepting a micron label as a complete specification.

This guide supports enquiries for INCEFILTER nylon filter mesh. It explains a comparison method, not a correction to any particular catalogue specification.

Understand the geometry before comparing percentages

For an ideal, uniform square opening with equal thread diameters in both directions, let a be the clear opening and d the projected thread diameter. The repeat pitch is a + d. The geometric open-area percentage is 100 × [a ÷ (a + d)]², using the same units throughout.

The relationship follows by dividing the opening area, a², by the repeat-cell area, (a + d)². It shows why increasing thread diameter at a fixed aperture reduces geometric open area. It does not calculate liquid flow or filtration efficiency.

For a hypothetical example, an opening of 120 µm with a thread diameter of 40 µm gives 56.25% geometric open area. Keeping the opening at 120 µm but increasing the thread diameter to 60 µm gives approximately 44.44%. These are original geometry examples, not available INCEFILTER grades or measured product data.

Ask which basis the quotation uses

Comparison field What to confirm
Aperture The definition, direction and applicable tolerance.
Thread dimensions The specified diameter or projected width in each direction.
Open area Whether the figure is calculated or measured, and the method used.
Fabric condition Whether the value represents the supplied finished mesh.
Construction Material, weave, thickness and any finishing treatment.

Do not apply the square-opening equation unchanged to a different weave or an unequal geometry. Ask the supplier for the appropriate basis. Where a title, table and drawing disagree, request one reconciled specification before approving the order; do not choose the most favourable percentage.

Keep throughput and strength as separate approval questions

A higher open-area figure alone does not establish a guaranteed throughput or acceptable mechanical strength. Review the liquid, particle loading, support and finished-part arrangement. Sefar discusses increased open area in its screening products, but the performance of a specific liquid-filtration assembly still needs its own assessment.

For a replacement trial, compare candidates under the same agreed conditions and measure the required process outcome. Confirm that the candidate still meets the dimensional and mechanical requirements. Do not trade away an essential support requirement solely to obtain a larger percentage.

Connect the fabric specification to the installed part

The weave’s open-area percentage and the assembly’s exposed flow window are different quantities. Use the exposed-area guide when clamps or sealed borders cover the fabric. Keep both descriptions on the approved drawing.

Send INCEFILTER your mesh enquiry with the current code, aperture and open-area requirements, part drawing, liquid conditions, quantity and destination. Ask for a documented construction and sample proposal, with any unresolved specification differences identified.

Technical reference: Sefar: Sifter and Screener Products, for the relationship between mesh design and open area. No Sefar product capability or commercial relationship is attributed to INCEFILTER.

TAGs: pleated liquid filter cartridges china 5 micron filter wholesaler how to choose industrial filter bags 0.22 Micron Pleated Filter Cartridges industrial liquid filter bags Polyester Felt Liquid Filter Bag Pleated Filter Cartridge Manufacturer Pleated Filter Cartridge Factory Pleated Liquid Filter Cartridges How to Choose a Reliable Pleated Filter Cartridge Manufacturer Pleated Liquid Filter Cartridges pleated membrane cartridges

Request a Quote

Our experts are here to help. We will respond within 24 hours to your request.

Get in Touch with Us

EMAIL: sales6@incefiltration.com
Mobile/WhatsApp: +86 186 3308 5625
TEL: +86 (311) 8968 1588
TIME: Monday-Friday 8:00am - 5:30pm (CST)

Request a Sample

Need a closer look? Most products have samples available to ensure you are ordering the correct product for your needs. Some restrictions may apply.

Send Us a Message

Tell us what you need, and we'll help you get quotes.

Mobile/WhatsApp: +86 186 3308 5625 Email: sales6@incefiltration.com



    Filtration Engineer
    ● Online
    ×
    WhatsApp