!! This website has permanently moved to this new domain: https://www.incefilter.com

High Flow Cartridge Temperature Derating: Read Pressure Limits Together

A maximum temperature and a maximum differential pressure are not automatically two limits that can be combined in every operating condition. When buying a high flow filter cartridge, ask for the permitted pressure difference at the actual service temperature, for the specified fluid and flow direction. Temperature derating means that an allowable limit is reduced as temperature changes.

Use the exact proposed part number when reviewing INCEFILTER high flow filter cartridges. A dimensional match or shared micron label does not establish an identical operating envelope.

Separate the pressure quantities

Housing pressure describes the pressure contained by the vessel. Cartridge differential pressure describes the pressure difference across the element. The housing’s allowable pressure does not establish the element’s allowable differential pressure, and an element rating does not qualify the housing.

For example, inlet and outlet readings of 4.0 and 3.4 bar gauge give a difference of 0.6 bar between those measurement points. This is an arithmetic example, not a recommended operating value. Depending on where the taps are located, the measured difference may include housing or connection losses as well as the element. Agree the measurement boundary before comparing it with a specification.

Look for paired temperature and pressure conditions

Pall’s published Marksman PFT high flow specifications illustrate the issue: the listed maximum operating differential pressure is lower at the higher of its two stated temperatures, with a specified normal flow direction. Those values belong to that Pall product family and must not be transferred to an INCEFILTER replacement.

Ask the supplier for a table, curve or written limit applicable to the offered construction. If only selected temperature points are given, request clarification for the intended operating point. Do not assume linear interpolation or extrapolate beyond the documented range.

Review each duty condition separately

Condition Information to provide
Normal production Fluid composition, temperature range, flow and expected pressure difference.
Startup Starting temperature, ramp procedure and any known pressure transients.
End of service Proposed change-out criterion and the evidence supporting it.
Cleaning or flushing Whether the element remains installed; liquid, temperature, duration and direction.
Abnormal or reverse flow Whether it can occur and what separate manufacturer limits or system protection apply.

Cleaning temperature is not automatically approved continuous service temperature. Likewise, a maximum differential pressure is not automatically a suitable alarm or routine change-out setting. Have the equipment supplier and responsible engineer confirm those settings for the complete system.

Keep hydraulic predictions and allowable limits distinct

A clean-element flow curve helps estimate pressure loss under its stated test conditions. An allowable differential-pressure limit describes an operating boundary. One does not replace the other. Review the viscosity and flow-curve assumptions alongside the operating limits.

Check the specified flow direction and all relevant component materials, including support parts and seals. Record the document revision used for approval so a later reorder can be checked against the same basis.

What to send with an inquiry

Send INCEFILTER the current cartridge code and drawing, housing identification, fluid composition, normal and exceptional temperature conditions, flow duty and proposed change-out criterion. Use our quotation inquiry page to request the applicable temperature and differential-pressure limits for the offered part. Do not approve service solely from a general product-family temperature statement.

Technical reference

Pall: Marksman PFT High Flow Series performance specifications provides an example of temperature-dependent differential-pressure ratings. The reference does not establish brand affiliation or replacement equivalence.

TAGs: pleated liquid filter cartridges china 5 micron filter wholesaler how to choose industrial filter bags 0.22 Micron Pleated Filter Cartridges industrial liquid filter bags Polyester Felt Liquid Filter Bag Pleated Filter Cartridge Manufacturer Pleated Filter Cartridge Factory Pleated Liquid Filter Cartridges How to Choose a Reliable Pleated Filter Cartridge Manufacturer Pleated Liquid Filter Cartridges pleated membrane cartridges

Request a Quote

Our experts are here to help. We will respond within 24 hours to your request.

Get in Touch with Us

EMAIL: sales6@incefiltration.com
Mobile/WhatsApp: +86 186 3308 5625
TEL: +86 (311) 8968 1588
TIME: Monday-Friday 8:00am - 5:30pm (CST)

Request a Sample

Need a closer look? Most products have samples available to ensure you are ordering the correct product for your needs. Some restrictions may apply.

Send Us a Message

Tell us what you need, and we'll help you get quotes.

Mobile/WhatsApp: +86 186 3308 5625 Email: sales6@incefiltration.com



    Filtration Engineer
    ● Online
    ×
    WhatsApp